STUKKOPATCH™

1 Gallon / Sand

$69.95 $79.95

STUKKOPATCH™

Coverage Rate: 25 - 50 Square Feet Per Gallon

Elastomeric Waterproofing Stucco Repair Compound, Patch, Crack Sealer & Caulk for Stucco, Cement and Other Surfaces.

$69.95 $79.95

Bucket Size 1 Gallon 5 Gallon

Finish Sand Coarse

Durable Sand or Rough Texture Finish
Cementitious Surface Repair Compound
Elastomeric Waterproofing
Superior Mold, Mildew and Fungi Resistance
High Strength Durability
Low V.O.C. & Environmentally Friendly
Easy Application and Water Clean Up

Need help? Call toll free 1-800-423-7264 to speak with a waterproofing expert.

STUKKOPATCH is a White, Pre-Mixed and Ready-To-Use Waterproofing Acrylic Resin Based, Trowel or Brush Grade Stucco and Wall Finish Sealant, Filler and Repair Stucco Patch. Designed to repair, patch and protect any irregularities, chips or cracks, on stucco, and other interior and exterior surfaces such as walls, floors and virtually any substrate, horizontal or vertical.

It is ideal for use with Stucco, Portland Cement, Block, Brick, Concrete, Wood, Metal and most other surfaces. It can also be used to create interesting decorative and highly durable interior finishes over drywall, plaster, walls, ceilings and pillars. STUKKOPATCH comes in ready-to-use for easy application.

It is a revolutionary 100% Acrylic Formulation with a trade secret mixture of High Solids Fillers to create a sealing patch and repair compound. It seals and forms a waterproofing, flexible, breathable, Sand or Coarse finish that has outstanding durability and has been designed to repair, waterproof, bond, seal and patch most surfaces to combat the destructive environmental forces of nature. Very easy to apply and can be painted over with most any latex paint or coating.

Parent ASIN:

B0DPNFDNNF

Parent SKU:

2740

Product Information

Solids By Weight: 86%
Weight Per Gallon: 14 lbs.
V.O.C.: 100 g/l

STUKKOPATCH™ SURFACE PREPARATION:
For proper adhesion to an existing substrate, it is recommended that the surface be pressure washed at a minimum of 1500 P.S.I., using a water and chlorine solution, removing any loose, flaking or peeling paint along with any dirt, oil, grease, residues and especially mold, mildew and algae. STUKKOPATCH™ will resist mildew growth but will not kill mildew already on the surface. Wire brush if necessary. Apply only to a sound, well prepared surface. If the surface remains chalky or is in poor condition after cleaning, a coat of ULTRA PRIME™ Stucco Primer is necessary. Rusted metal must be primed prior to application of STUKKOPATCH™. Inquire about SUPERMAX™ Metal Primer Rust Treatment Process. All other non-cement-based surfaces must be primed first with ULTRA PRIME™ prior to the application of STUKKOPATCH™.

STUKKOPATCH™ APPLICATION PROCEDURE:
Do not thin, use product as is. Do not apply when temperatures are below 45 degrees Fahrenheit or when humidity is very high. Do not apply when caulk will be subjected to rain or heavy dew before it has had enough time to dry (approximately 4 to 6 hours). Drying time will vary depending on temperature, humidity and location. Apply STUKKOPATCH™ with a caulk gun, trowel or stiff brush to the prepared surface. NOTE: STUKKOPATCH™ allows minimal shrinkage, but the thicker it is applied, the more it will shrink. Evaluate after 12 hours to determine if additional STUKKOPATCH™ is required. When filling deep holes, more than 1 square inch, apply multiple coats and build the patch up to allow for minimal shrinkage. Sets to touch in approximately 2 hours and dries in approximately 5 to 24 hours depending on thickness of application. The thicker the STUKKOPATCH™ is applied the longer it will take to dry. STUKKOPATCH™ can be coated over in 12 hours but be careful not to disturb the patch since it will dry from top to bottom and may still be soft. STUKKOPATCH™ must be top coated with a compatible latex paint or coating and should not be left uncoated.

CLEAN UP:
Clean up all spills, tools and equipment immediately while it is still wet with warm soapy water.